AK Master Mount™ Enhanced Safety Lever

$60.00

We have taken the traditional AK safety lever and “tactically” enhanced it for the modern AK user. The AK Master Mount™ version of the AK safety lever is rugged 16 gauge steel (1.5 mm thick), has an improved ergonomic extended side tab, bolt-hold open feature, and is fully compatible with the AK Master Mount™ side rail mounting hardware.

Available in AKM and Yugo versions. Semi-auto or Full-auto configuration. With or without bolt-hold-open (BHO) notch.

Note: Not compatible with underfolder stocks.

5-Minute Installation

All of our components can be installed in 5 minutes or less. No gunsmithing required.

J

Easy On / Easy Off

If our AK-47 accessories are uninstalled, your weapon is back to factory conditions.

Built to Last

Materials as rugged as the AK itself.

No Other Safety Lever Compares

Our AK Master Mount™ safety lever safety levers are stamped from heavy duty 16 gauge (.060" or 1.5 mm) thick steel, thicker than all the other AK safety levers on the commercial market or those made by the factory!  The extended side tab is also thick 16 gauge steel.  This makes it rugged and robust, and it will not cut your finger like the safety levers with "razor thin" side tabs.  The side tab is textured on BOTH sides for better traction, especially if wearing gloves.  The tab is also flat to be easy to move the safety lever in the up AND down directions, and it is angled slightly upward from back to front to be more ergonomic.  Then finally it is heat treated to Rockwell C hardness of 30 for added toughness.  

Solid Steel

The internal paddle part of the AK Master Mount™ enhanced safety lever is milled from solid steel.  It is NOT cast like most of the AK safety levers these days. It is heat treated to Rockwell C hardness of 30 for even more toughness.

Yes, we overbuild our products as we are AK purist.  We make a semi-automatic and full-auto configuration.

 

 Correct Safety Lever Stop

The lower edge has the correct embossing to prevent the safety lever from over-riding the safety lever stop tab that extends up from the trigger well. 

 

 

Robust Construction

The distal end of the AK Master Mount™ enhanced safety levers have a stiffening ridge incorporated into the stamping to provide greater strength and rigidity under the bolt-hold-open notch.  There is also a distal smaller side tab for an additional finger purchase point, plus it adds even further strength to the end of the lever. 

Bolt Hold Open Notch (BHO) Version

Since many shooting ranges require the bolt to be open when the firearm is not in use, our enhanced safety levers come with a bolt hold open notch. The front edge of the notch is "hook shaped" to firmly wrap around the charging handle.  This Bolt Hold Open notch is a version available in both our AKM and Yugo version safety levers.

 

No Bolt Hold Open Notch (BHO) Version

Since many AK users prefer a more traditional looking safety lever, we also offer our AKM version enhanced safety levers (both semi-auto or full-auto configurations) in a no BHO notch version.

NOT available in our Yugo version safety levers.

 

 

Semi-Auto or Full-Auto Configuration

Our AKM versions are available in a semi-auto or full-auto configuration, with or without BHO notch feature.  The semi-auto configuration has a notched internal paddle component so that engagement with a full-auto sear can not occur.

AKM ENHANCED SAFETY LEVER VERSION

AKM Version

Our AKM version enhanced safety lever is for the stamped receiver.  It can be modified to fit thicker milled receivers by enlarging its "gap."  See our website's "support" tab for further information.

This AKM version does not fit "Yugo" AKs.

View the "Installation" section under the "Support" tab on this website for installation video, tips, and troubleshooting guide.

Disclaimer: As with any AK accessory part, slight modifications may be needed for proper fitting.

YUGO ENHANCED SAFETY LEVER VERSION

Yugo Version

This current version is for the "Yugo" style stamped receiver.  We continue our "rugged" theme by making the external part of this safety lever from 16 gauge (.060" or 1.5 mm) thick steel; thicker than the other AK safety levers sold. The extended side tab is also 16 gauge thick steel.

Note: This Yugo version does not fit "AKM" style AKs.

View the "Installation" section under the "Support" tab on this website for installation video, tips, and troubleshooting guide.

Disclaimer: As with any AK accessory part, slight modifications may be needed for proper fitting.

MISCELLANEOUS TECHNICAL INFORMATION

 

Our full auto version safety levers are compatible with the CMC AK 2.0 Elite™ drop-in trigger group.

 

 

Our AKM version safety levers are dimensionally similar to the Russian / Bulgarian safety lever.  This can be used as a guide for determining "fitment" in your particular AK.  For example, when paired with the ALG™ AK drop-in trigger unit, their roll pin will be needed to ensure proper contact with the internal paddle part of our safety lever.

 

The ubiquitous AK product disclaimer applies: "As with any AK accessory part, slight modifications may be needed for proper fitting on a particular AK".

 

Related products